Solved The gear ratios of a 5-speed manual transmission are
The transmission is used for a FWD car with the following data: Front axle weight: 1450 lbs Center of gravity height: 14 inch Air drag coefficient: 0.30 Tire radius: 10.0 in. Powertrain efficiency: 0.93 Rear axle weight: 1250 lbs Wheel base: 102 in. Frontal projected area: 21.00 square feet Roll resistance coefficient: 0.02 Road adhesion ...
Solved Fifth synchronizer Fifth gear driveshaft pinion gear - Chegg
Draw the power-flow for 1st, 2nd, 3rd, 4th, 5th gears and reverse gear on the manual transaxle images below. Fifth speed gear Fifth gear Fifth synchronizer driveshaft Driveshaft - pinion gear Fifth speed gear Driveshaft - Input cluster - gear shaft Main shaft Input cluster - …
Solved Problem 2 (5 pts): A vehicle is being operated on a - Chegg
Problem 2 (5 pts): A vehicle is being operated on a highway with the reference velocity of 126 km/h (35 m/s) in gear 4 and it overcomes the total load torque of 300 ft-lb. This vehicle specification includes effective wheel radius of 0.35 m and 4th gear ratio of 2. What throttle angle is required for maintaining the current speed of the vehicle?
Solved 34. Draw the power-flow for 1st, 2nd, 3rd, 4th, 5th - Chegg
Draw the power-flow for 1st, 2nd, 3rd, 4th, 5th gears and reverse gear on the manual transmission images below and describe the path of the power through for each gear selection. Input shaft bearing Output shaft bearing wwwwwwwwwwwwwwwwwwww WWW WWWWWWWW Rear counter shalt bearing Front counter shaft bearing Countershaft assembly 1st Gear Input ...
Solved 12. What is the overall speed ratio of the following - Chegg
12. What is the overall speed ratio of the following 3 1M gear 24 teeth 2nd gear 16 teeth gear 64 teeth gear 8 teeth o Questions 13-15 refer to the diagram below. 10 9.75 10 12.5" 4.25 876 RPM Pulley and Gearing Calculations 13. What is the speed of …
Solved A sports car accelerates approximatelu as shown in - Chegg
Answer to A sports car accelerates approximatelu as shown in. Estimae the car's average acceleration in (a) second geas gear and (b) fourth gear. 50 5th gear 4th gear 40 el gear 30 20 2nd gear 10 1st gear r (s) 30 40 Figure 1: The velocity of a …
Solved The stick diagram of a 6-speed FWD MT is shown below
The numbers of teeth are labeled in the drawing for clarity. The gear ratios from the 1" to the 4th gears are: first gear (3.92), 2nd gear (2.76). 3rd gear (1.85), 4th gear (1.35). The numbers of teeth of the final drive gears are: Nr 21, NF. 66. a) The vehicle runs in the 5th gear at a speed of 55 mph with the engine speed at 2500 RPM.
Solved A 3-mile long and 40-foot-wide stabilized portion of - Chegg
A 3-mile long and 40-foot-wide stabilized portion of a two-lane road requires mixing, spreading, and finishing. The mixing operation requires 3 passes in 1st gear, spreading requires 2 passes in 3rd to 4th gear, and finishing requires 6 passes in 2nd to 4th gear. Use conservative speeds.
A 1996 Dodge Viper GTS has the engine torque curve - Chegg
Question: A 1996 Dodge Viper GTS has the engine torque curve and gear ratios shown in the followingtable. The rear tires have a nominal radius of 13in. Generate a plot of force at the roadversus vehicle speed for each gear. Your result should …
Solved The stick diagram of a 6-speed FWD MT is shown below
First, calculate the transmission ratio for the initial gear using the formula , where is the number of input gear teeth and is the number of output gear teeth. View the full answer Previous question Next question