Dec 30, 2024 · Note: Most HF plasma cutter (but not all) have a built in gap between the electrode and the cutting tip. This is like a spark plug gap. Note: All electrodes (negative) are isolated from the outer threads (positive) on all plasma cutters HF as well as blow back units. Now first all HF plasma cutters do NOT have a pilot arc.

Mar 5, 2022 · This is what I have found to work with most plasma cutter nozzles/tips that most people have in their shops or garages. NOTE: Orifice hole size 1mm = .03937" 20 amp tip - 0.6mm/.025" - 15 to 20 amps - 50 to 55 psi. 30 amp tip - 0.8mm/.030" - 21 to 30 amps - 55 to 60 psi. 40 amp tip - 0.9mm/.035" - 31 to 40 amps - 65 to 70 psi

Jan 27, 2021 · Any font can be used for plasma cutting. There are some that just won’t work well though. Papyrus comes to mind Any font with extremely fine detail flourishes or stroke portions can lose those details when the plasma’s kerf is accounted for. Blocky fonts, stenciled ones for folks who don’t want to manually add bridges are very safe.

Sep 18, 2020 · I use F5 bend of nitrogrn and hydrogen for cutting stainless steel. I have 3 large bottles of it plumbed into plasma cutter via hydrogen regulators. F5 gas cuts very similar to nitrogen or air. It leaves the edges of the stainless smooth and clean. It requires less amps and faster speed due to the hydrogen molecules. So I’m told. It works well.

Apr 9, 2020 · A1. Verify that your plasma cutter’s 50:1 voltage divider port is functioning properly while cutting. If your plasma cutter is equipped with a 50:1 voltage divider in the CNC port (called a CPC port on Hypertherm), we will use your DMM to measure the DC Voltage across the two pins of this port while the plasma cutter is cutting.

Jul 30, 2022 · Where to purchase consumables for your Everlast Power Plasma 82i The Hypertherm Powermax 85 now has a cartridge consumable that cost $53.00 each!!! I can run a 33" x 48" sheet of 1/4" thick plate with a ton of parts without burning threw a set of consumables.

Oct 3, 2018 · Just wondering if the everlast power plasma 60s with it’s cnc ready plug will work the same way as stated above about connect the table to plugs 1&2 Thank you in advance! KX9M September 19, 2019, 3:17am

Aug 9, 2018 · Yes, I would go with a Razorcut or an Everlast. PT60 style torches have reasonably priced consumables as well. You are looking for a plasma cutter with a “Pilot Arc.” Check your local craigslist for cheap used plasma cutters as well. HF units are getting harder and harder to find (good) so just make sure it is a pilot arc ignition.

Dec 20, 2021 · So about two months ago I hooked my Everlast Power plasma 82i to my Crossfire Pro table. I wired it up using the CNC plug that comes with the 82i. I’m using the raw voltage and trigger pins on the CNC plug. The one word that best describes my experience with the Everlast 82i would be “consistent” Using the 1.3mm tips @75 amps I can cut 11 gauge at 220 IPM, 1/4" …

Dec 13, 2018 · new to plasma cutting I’ve looking at the form but not able to find a simple chart for perfect cut on 11 gauge, 14 and 16 mild steel (I’m getting a lot of dross) someone here probably dialed everything perfectly pls share with us. using-Razorcut30i with 0.8 tip (or any suggestion)-Langmuir Systems-Fusion 360